It’s no fun taking your bike to the LBS only to hear that your problem is user error. Mechanics face these five customer woes all the time. Here’s how to solve them yourself. — By Lindsay J. Westley
Degreasing Your Chain
Problem: My chain isn’t shifting correctly, and it skips a lot.
What Happened: You may be an over luber, and the excess sticky stuff is attracting grime to the chain and cassette. First clean, rinse, and dry your chain and cassette (the gears in the back). You can buy bike-specific degreasers and chain-cleaning gizmos, but dish soap and a toothbrush work, too. Next, carefully apply one drop (more is not better) of lube onto each roller as you turn the cranks backward for two or three rotations. Finally, take a clean rag and gently grip the chain’s outer plates as you spin the cranks for one more rotation. Keep going until you’ve wiped off all the excess lube—it should be mostly inside the chain on the rollers, not on the outside where it can attract dirt.
It’s no fun taking your bike to the LBS only to hear that your problem is user error. Mechanics face these five customer woes all the time. Here’s how to solve them yourself. — By Lindsay J. Westley
Aligning Your Wheel
Problem: I fixed a flat. Now the tyre is rubbing one of the brake pads.
What Happened: You reinstalled your wheel crooked.If you slid the skewer all the way out to remove your wheel, you might have dropped one of the two skewer springs—which help keep your wheel centred—or reinstalled them backward. Check to be sure the narrow side of the spring is next to your hub; otherwise, it could increase the axle diameter and affect fit. Tip: You don’t have to remove the skewer completely to take off a wheel. Just open the quick-release lever and spin the nut on the other side to loosen, then gently dislodge it from the dropouts (slots in the frame and fork where each skewer rests). When tightening, keep the bike on the ground to help the wheel sit properly.
It’s no fun taking your bike to the LBS only to hear that your problem is user error. Mechanics face these five customer woes all the time. Here’s how to solve them yourself. — By Lindsay J. Westley
Inflating Your Tyres
Problem: I keep getting flat tyres. Are my tubes defective?
What Happened: You’re under-inflating your tubes, there’s debris inside the tyre, or you’re not installing them correctly. Low tyre pressure can cause a tube to be pinched against the rim and result in what’s called a pinch flat. Look on the side of your tyre to find the recommended PSI (pounds per square inch) range. Inflate the tube to at least the lower number. If you’re a heavier rider (more than 100kg including your bike), fill it to the maximum number. When changing a tyre, run your finger along the inside to check for foreign objects (such as a tiny piece of gravel or glass) that could cause another flat. Before you inflate a new tube, check to make sure it isn’t caught between the rim and the tyre.
It’s no fun taking your bike to the LBS only to hear that your problem is user error. Mechanics face these five customer woes all the time. Here’s how to solve them yourself. — By Lindsay J. Westley
Adjusting Your Shifter
Problem: My chain keeps popping off. Can you adjust my shifter?
What Happened: You didn’t soft pedal when shifting between chainrings.
When you pedal hard while shifting, especially on hills, the chain has to work harder to move since it’s already under heavy resistance. Try easing off as you shift gears. You won’t lose momentum, but by avoiding a last-minute, panicked shift, your chain should move exactly where you want it to go. If you are soft pedaling but still dropping your chain, you may need a professional to adjust the limit screws on your front derailleur (the part that moves the chain between rings). These screws allow you to make precise adjustments, but even a small turn can cause damage if you’re not sure what you’re doing.
It’s no fun taking your bike to the LBS only to hear that your problem is user error. Mechanics face these five customer woes all the time. Here’s how to solve them yourself. — By Lindsay J. Westley
Cleaning Your Chain
Problem: My chain is making a grinding noise. Can you quiet it down?
What Happened: You’re cross-chaining or not cleaning and lubing your chain often enough.If your chain is grating or rasping when you’re in your big chainring in front and your biggest sprocket in back (or vice versa), you’re increasing wear and tear on your components–which will cost you money in the long run. Try clicking down two or three gears in the back and/or shifting into your smaller chainring. If that isn’t the problem, it may be time to clean and lube your chain. Aim to do it at least every few weeks, and after any wet or muddy ride. If neither of these solutions works, you may want to consult with a mechanic. Your chain may be worn (and you’ll need a new one) or your derailleurs need to be adjusted.
It’s no fun taking your bike to the LBS only to hear that your problem is user error. Mechanics face these five customer woes all the time. Here’s how to solve them yourself. — By Lindsay J. Westley
It’s OK to…
1. Take your bike to the shop even if you think you can do the repair yourself. A quicker fix means more riding time for you.
2. Ask a mechanic what caused the problem and ask him or her to explain it again if you don’t understand.
3. Go back to the shop after riding 40-80km on a new bike. (In fact, you should.) Components settle and shift during these first few rides, and you’ll want a pro to readjust them for you.